« Do You Believe in Magic? | Main | Getting All Touchy Feely »

Incase Snap Case + Stand for iPhone 4

Incase Snap Case + Stand for iPhone 4

So a few weeks back I ordered this Incase Snap Case for the iPhone 4 through Apple's "We're Sorry You're Making Such a Big Deal Out of Nothing" program. ;-p It's not that I really needed it, having already gotten the ifrogz LuxeLean case beforehand which still works just fine. But who am I to turn down a free case? At the time it said shipping would be in 4 weeks so I think this came a little early.

Incase Snap Case - Front View

As far as iPhone cases go, this one is pretty typical of the clear acrylic form-fitting cases I've had in the past with my previous iPhones. Compared to the ifrogz, as far as I can tell, it may be just a smidgen thinner but seriously, just splitting hairs at this point.

Incase Snap Case - Side View

The left side of the case is a bit more encased compared to the ifrogz with separate cutouts for the ringer/vibrate switch and volume buttons. The case is thin enough so that operating these controls doesn't take too much getting used to compared to having just the phone uncased. Not sure why they embossed the "Made in China" on the inside of the case but that doesn't affect anything. The right side of the case I didn't bother taking a photo of cause it's just straight covered plastic with an embossed Incase logo towards the bottom.

Incase Snap Case - Top View
Incase Snap Case - Bottom View

The top and bottom of the case is pretty much exactly the same as on the ifrogz case. No surprises here. Easy access to all the controls, plugs and jacks at the expense of not so thorough protection.

Incase Snap Case - Back View

And as you can see the back is pretty nondescript. The cutout for the camera lens + flash is not as form-fitting as on the ifrogz plus they encircled the edges of the cutout with what they call a "Flash Ring." Basically they just made the edges black so it cuts down on possible glare caused by the flash reflecting on the clear acrylic and bouncing back into the lens. I'm not a heavy flash user so not sure if this is truly useful or not but sounds good at least. =p You'll also notice from this shot of the back that like all clear acrylic cases, this one also picks up fingerprints quite easily.

Incase Snap Case + Stand

You do get a bonus with this case though: a little dual-sided clear acrylic stand. Incase tends to include these little stands with their thin cases. I remember having a S-shaped black plastic one for the iPhone 3GS when I got their perforated case. They're cheap and kinda dinky but convenient and perfectly functional in a pinch.

Stand Angle 1
Stand Angle 2

As I mentioned it's dual sided so you can place the iPhone in at one of two angles. Not entirely sure what exact angles they are but something like 45 and 60 degrees would be my guess. And they only work with the iPhone placed horizontally. The iPhone will tip over backwards immediately if you place it vertically in the 45 degree angle. With the 60 degree it'll work but once you put any pressure on the phone it'll tip over. So just keep it in the horizontal position.

So, in a nutshell, this Snap Case is good if you're a real basic, no frills kinda guy. It's light and thin and gives you just the most basic of protection, mostly just against scratches. If you like to show off the look of the iPhone but still want some protection on it, then this case will be good for you. Like all clear acrylic cases though, I predict that the back of this one will wind up getting all scratched up after a couple of weeks. Better the case than the iPhone itself obviously but these types of cases don't usually retain their pristine forms for very long. Plus you'll have to wind up removing the case every now and then to clean out the tiny dust particles that will inevitably work its way in-between the back of the case and the iPhone itself. If you don't do this often, some of those particles can wind up scratching the iPhone. That may be less of an issue with these new iPhone 4s and their glass backs but it was definitely an issue on the previous iPhone 3GS.

Compared to the ifrogz LuxeLean, I probably favor the ifrogz a bit more at this point. The ifrogz, because of the colored paint has a more grippier feel to it than the Incase which can be quite slippery if you're not careful with it. And I like the felt-like backing that covers the interior of the ifrogz. That pretty much traps any wayward dust particles that make their way into the case and prevents them from moving around against the back of the phone. But besides that, both cases give you pretty much the same amount of protection with the least amount of size and weight addition.

TrackBack

TrackBack URL for this entry:
https://www.hitokiri.com/cgi-bin/mt-tb.cgi/1836

Comments (2)

applebook:

I had the iFrogz, which was free throw in, and I gave it away because of its horrible look and cheap construction. I wouldn't let my expensive and lovely iPhone 4 touch that.

I also have a stand case and like it very much. Not only does it aim to protect your device from scratches, scuffs, and scrapes, but it also boasts a built-in stand with a choice of different viewing angles.

Post a comment

About

This page contains a single entry from the blog posted on August 11, 2010 12:21 PM.

The previous post in this blog was Do You Believe in Magic?.

The next post in this blog is Getting All Touchy Feely.

Many more can be found on the main index page or by looking through the archives.

Subscribe

 

Add to Google Reader or Homepage
Creative Commons License
This weblog is licensed under a Creative Commons License.